AIRTRONICS M12 Guía de usuario descargar pdf (Pagina 22)



 

TELEMETRY Screen Overview Diagram Descriptions, Continued....

Numerical Telemetry Data: Displays the Telemetry Data in a numerical format.

Page Indicator: Indicates the current Page within the Telemetry Data Stream that Telemetry Data is currently being displayed on.

Receiver Voltage Display: Displays the current Voltage of the receiver battery. The tick mark indicates the current Voltage relative

to the programmed Maximum Voltage value.

RPM/Speed Display: Displays the current RPM or speed in MPH or KM/H.

RPM/Speed Gauge: Displays the current RPM or speed in MPH or KM/H in graphical format. The needle indicates the

current RPM or Speed relative to the programmed Maximum RPM or Speed value.

Status Indicator: Indicates the current Status of the Telemetry system. When VIEW is displayed, the Telemetry system is in VIEW

mode, allowing you to view and analyze Telemetry Data. When REC is displayed, the Telemetry system is Recording Telemetry

Data. When LOG is displayed, the Telemetry system is in Standby.

Steering Output Display: Displays the current position of the Steering channel as a percentage of Steering Wheel travel.

Telemetry Data Graph: Displays the Telemetry Data Stream in a graphical format.

Temperature 1 Display: Displays the current temperature in Fahrenheit or Celsius of the Temperature Sensor plugged into the

TEMP1 Sensor Port in the receiver. The tick mark indicates the current temperature relative to the programmed Maximum and

Minimum Temperature values.

Temperature 2 Display: Displays the current temperature in Fahrenheit or Celsius of the Temperature Sensor plugged into the

TEMP2 Sensor Port in the receiver. The tick mark indicates the current temperature relative to the programmed Maximum and

Minimum Temperature values.

Throttle Output Display: Displays the current position of the Throttle channel as a percentage of Throttle Trigger travel.

Reviewing Telemetry Data:

When the Telemetry Data Recorder has Stopped, you are able to view Telemetry Data in more detail. For more information about

Starting and Stopping the Telemetry Data Recorder, see the

Telemetry Data Recording

section on page 48.

1) After Stopping the Telemetry Data Recorder, press the SELECT switch to open the desired TELEMETRY page, either ST, TH,

RPM, VOLT TMP1 or TMP2.

5) To choose a different VIEW menu option, press the BACK key, then repeat steps 3 and 4 to choose and highlight the desired

VIEW menu option.

When viewing the Telemetry Data Stream using the VIEW option menu, keep these things in mind: When a VIEW menu

option is surrounded by a box, scroll UP or DOWN to choose a different VIEW menu option. When a VIEW menu option is

highlighted, scroll UP or DOWN to scroll through the Telemetry Data Stream. Press the BACK key to cancel the highlighted VIEW

menu option and choose another VIEW menu option.

As you're scrolling through the Telemetry Data Stream, press the ENTER key at any time to Open a detailed list of Telemetry

Data Entries. The highlighted Telemetry Data Entry at the top of the list is the one where you pressed the ENTER key.

2) Press the ENTER key. The VIEW menu will open and PAGE will be surrounded

by a box.

3) Scroll UP or DOWN to Select the desired VIEW menu option.

CURSOR - When chosen, scrolls through the Telemetry Data Stream in 0.5

second intervals.

PAGE - When chosen, scrolls through the individual pages of the Telemetry Data

Stream.

LAP - When chosen, scrolls through each counted Lap Time along the Telemetry Data Stream.

LAP-LT - When chosen, displays Total, Best and Average Lap Times, in addition to individual Lap Times.

SAVE - When chosen, allows you to Save the Telemetry Data Log to your PC.

4) Press the ENTER key to highlight the desired VIEW menu option, then scroll

UP or DOWN to scroll through the Telemetry Data Stream via the VIEW menu

option you chose. You can also press the SELECT switch RIGHT or LEFT to

view different TELEMETRY pages.

If you choose the SAVE option to Save the Telemetry Data Log to your PC,

see the

LINK

Menu Saving the Telemetry Data Log

section on page 58

for information on how to do this.

1 2 ... 17 18 19 20 21 22 23 24 25 26 27 ... 115 116

Comentarios a estos manuales

Sin comentarios

AIRTRONICS M12 Guía de usuario Pagina 22

Comentarios a estos manuales

Relacionado con productos y manuales para Controles remotos AIRTRONICS M12