AIRTRONICS MT-4s Guía de usuario descargar pdf (Pagina 27)

T R



The Auxiliary 1 Programming function allows you to program the six different Auxiliary Programming functions that are

controlled by Auxiliary 1 Channel 3. Use the table below to determine the different functions that are available:

IMPORTANT: Prior to programming an Auxiliary 1 Programming function you must first choose the desired Auxiliary

Programming function in the SYSTEM AUX TYPE menu. Only one Auxiliary 1 Programming function can be Active at any

given time.

The Step Auxiliary function allows you to program the Auxiliary 1 servo to move a defined amount when toggled ON and OFF

using a Push-Button Switch. For example, if you assign Auxiliary 1 to a Push-Button Switch, then program the Step Auxiliary

percentage value to 50%, the Auxiliary 1 servo will travel from the Neutral position to 50% of travel when the Push-Button Switch

is pressed. Press the Push-Button switch a second time and the Auxiliary 1 servo will travel back to the Neutral position. This

is useful to control simple ON/OFF functions, such as a reverse servo for a transmission or a mechanical switch to turn lights

ON and OFF, etc.

The Step Auxiliary Position value can be adjusted while you're driving using one of the four Trim Switches, the Rotary Dial

or the Auxiliary Lever. The Step Auxiliary function can be toggled OFF and ON by assigning Auxiliary 1 to one of the two

Push-Button Switches. This allows you to control when the Auxiliary 1 servo travels to the programmed Step Auxiliary position.

PROGRAM











STEP AUX

POINT AUX

4WS MIX

MOA MIX

AUX MIX

CODE AUX

Step Auxiliary

Point Auxiliary

Four Wheel Steering Mixing

Motor on Axle Dual Throttle Mixing

Auxiliary Mixing

CODE Auxiliary

Controls Step Values That the Auxiliary Servo Travels

Control Specific Points That the Auxiliary Servo Travels

Control Four Wheel Steering Options

Controls Dual Throttle Options (Dig and Burn)

Control User-Defined Auxiliary 1 Channel 3 Mixing Options

Controls SSL Equipped Accessories, Such as ESCs

FUNCTION FUNCTION NAME FUNCTION DESCRIPTION









Adjusting the Step Auxiliary Value:

1) From the Top Screen, press the ENTER key to open the Programming Menu list.

2) Scroll UP or DOWN to highlight the AUX1 menu, then press the ENTER key. The AUX1

STEP menu will be displayed and <AUX1 POSI> 0 will be shown.

3) Press the ENTER key, then scroll UP or DOWN to change the Auxiliary 1 Position value.

Increasing the value toward the High side (H) or Low side (L) will cause the Auxiliary 1

servo to travel to that specific position when you Activate the Auxiliary 1 Step function.

AUX1 STEP AUX1 POSI setting range is H100 to L100. The default setting is 0. This value

is a percentage of Auxiliary 1 servo travel.

Choosing the Step Auxiliary Function:

1) From the Top Screen, press the ENTER key to open the Programming Menu list.

2) Scroll UP or DOWN to highlight the SYSTEM menu, then press the ENTER key. Scroll

DOWN to highlight the AUX TYPE menu, then press the ENTER key.

3) Press the ENTER key, then scroll UP or DOWN to choose the AUX1:STEP AUX function.

Controlling the Step Auxiliary Function:

1) In the default configuration, Auxiliary 1 is controlled by the Rotary Dial which allows the Step Auxiliary function to be adjusted

while driving. Turn the Rotary Dial clockwise to increase the Position High Side value and turn the Rotary Dial counter-clockwise

to increase the Position Low Side value. In addition, Auxiliary 1 can be assigned to one of the four Trim Switches or the

Auxiliary Lever. The Step Auxiliary function can be toggled OFF and ON by assigning Auxiliary 1 to one of the two Push-Button

Switches. This allows you to control when the Auxiliary 1 servo travels to the programmed Step Auxiliary position. For more

information, see the Key Assignments section on pages 53 through 58.

1 2 ... 22 23 24 25 26 27 28 29 30 31 32 ... 87 88

Comentarios a estos manuales

Sin comentarios

AIRTRONICS MT-4s Guía de usuario Pagina 27

Comentarios a estos manuales

Relacionado con productos y manuales para Controles remotos AIRTRONICS MT-4s