AIRTRONICS VG6000 Instrucciones de operaciones descargar pdf (Pagina 4)

Global Hobby Distributors

18480 Bandilier Circle

Fountain Valley, CA 92708

http://www.airtronics.net

3) Move the transmitter control sticks to the desired Fail Safe position. While holding the transmitter control sticks in those positions

(generally throttle at idle and a minimal amount of elevator and/or aileron), press and hold the Bind Button on the receiver. After ~2

seconds, the Bind LED will begin to blink slowly. Continue holding the Bind Button until the Bind LED begins to blink rapidly (~2 more

seconds). Once the Bind LED begins to blink rapidly, release the Bind Button.

4) Turn the transmitter OFF to test Fail Safe operation. The servos should move to the positions that you set in step 3.

The Fail Safe settings will be erased if you re-bind the transmitter/receiver pair. If you bind the same transmitter/receiver pair

you MUST repeat these procedures to setup the Fail Safe function again.

1) Drop the throttle control stick all the way back to the Low Throttle position, then turn the transmitter ON.

2) Turn the receiver ON. The Bind LED on the receiver should illuminate solid blue, indicating that the transmitter and receiver are

paired, then move the transmitter control sticks to verify that the servos are operating.

Programmable Fail Safe is available on channels 1 through 4 only.

settinG tHe FailsaFe

The Fail Safe function automatically sets the servos to a predetermined position in the event that the signal between the transmitter and

the receiver is interrupted, whether due to signal degradation or to a low transmitter battery. For example, the Fail Safe can be set so that

the throttle servo returns to low, the elevator moves slightly up, and the ailerons move slightly right or left, to result in a shallow decent.

ranGe cHeckinG - low Power mode

IMPORTANTTheradiocontrolsystemshouldberangecheckedpriortotheday'srstightandpriortotherstightafterahard

landingorafterarepair.Thiswillensurethatthetransmitterandreceiverarecommunicatingproperlypriortoight.Thisensuresthe

safety of your model, yourself, and the people around you.

1) Press and hold the Bind Button on the transmitter, then turn the transmitter ON. Continue to hold down the Bind Button for ~5 seconds.

The Bind LED will blink slowly during this time. After ~5 seconds the Bind LED will blink rapidly, then go out. Release the Bind Button

and the Bind LED will continuously blink rapidly. The transmitter is now in Low Power Mode.

Do not attempt to fly with the transmitter in Low Power

Mode. You will be unable to control your model once it is a

certain distance away from you. Before you fly, make sure

that the Bind LED is illuminated solid blue!

If, after checking all airborne system components and verifying correct antenna wire mounting, your radio control system still fails

the Range Check, DO NOT FLY. Please contact Airtronics Customer Service.

The transmitter will stay in Low Power Mode for 3 minutes. After 3 minutes, the transmitter will revert to Normal mode.

2) Turn the receiver ON in your model.

3) With the transmitter in Low Power Mode, walk approximately 30 paces from your model (approximately 90 feet) and, with the help

of another person, check to make sure that the servos move without any problems. If there is a problem with servo movement, try

moving to a different position while still maintaining the same distance from your model, then check servo movement again. If there

is still a problem, DO NOT FLY. Check to make sure that all receiver, servos, switch, and onboard battery connections are correct

and secure. Check to ensure that the antenna wires are correctly mounted.

4) After you have completed your range check, turn the transmitter OFF, then turn the transmitter ON to revert back to Normal Mode.

Low Power Mode

Normal Mode

POWER MODE TX BIND LED STATUS

Blue - Blinking Rapidly

Blue - Illuminated Solid

The Range Checking procedure describes using the receiver with an Airtronics RDS8000 2.4GHz transmitter. If using the receiver

with an Airtronics SD-10G 2.4GHz transmitter, please refer to the Range Checking section in your SD-10G Operating Manual.

Telephone: (714) 963-0329

Fax: (714) 964-6236

Email: [email protected]

Airtronics is Distributed Exclusively in North America by:

1 2 3 4

Comentarios a estos manuales

Sin comentarios

AIRTRONICS VG6000 Instrucciones de operaciones Pagina 4

Comentarios a estos manuales